Live Stoner Chat Live Stoner Chat - Apr-Jun '24

[JP1]

The hole in this is soooo small it takes a few seconds of blowing through it to get air to come out. I wonder if it was like this always, and never noticed. It was a drop then nothing. Then a little later another drop. It's not like a flowing leak, but eventually it will be bigger. It looks like it's where the seems meet it was a little thin. I have bong that seeps where parts meet. It just slowly collects on the outside of the glass. You wipe it away, and then a little later there it is again. Never runs down the little bit of water like plugs the tiny holes. Very odd, but as wise old man to me "I've seen that fish before" lol. I don't have any good silicone all I have has hardened. I was think about giving it a spray with flex seal just not sure if that's safe with it coming into contact with water.

You could hot knife it and melt the plastic back together

 

[Frankthetank]

You could hot knife it and melt the plastic back together

They sell plastic welding kits at harbor freight….that way you have filler…probably more expensive than a new piece…

Although jb weld would work, I suppose…

 

[McDee]

You could hot knife it and melt the plastic back together

I thought about that, melt a zip tie on it maybe. That is on the table, but kinda later option because I could end up melting the whole thing lol.

 

[Mañ'O'Green]

Good Morfnoevight All! EO'n'Dabs.

I felt like I needed to go to confession after eating these:

 

[Lil Dab]

 

[Bill.de.Cat]

The hole in this is soooo small it takes a few seconds of blowing through it to get air to come out. I wonder if it was like this always, and never noticed. It was a drop then nothing. Then a little later another drop. It's not like a flowing leak, but eventually it will be bigger. It looks like it's where the seems meet it was a little thin. I have bong that seeps where parts meet. It just slowly collects on the outside of the glass. You wipe it away, and then a little later there it is again. Never runs down the little bit of water like plugs the tiny holes. Very odd, but as wise old man to me "I've seen that fish before" lol. I don't have any good silicone all I have has hardened. I was think about giving it a spray with flex seal just not sure if that's safe with it coming into contact with water.

Mine was like a drop every 10 or 15 seconds. Very hard to notice until quite a few drops built up with the lights off. I guess it was slow enough that it was just evaporating away before building up a puddle. My thought was to hit the auto parts store for vacuum line adaptors but seems they really don't carry much in that department anymore. I remember in the 80's getting anything and everything from 1/2 inch down to 1/16 inch in straights, 2 way, 3 way, 4 way and 8 way manifold.

 

[N/A-Greengo]

Mephisto Genetics
Mephistoreoz
Day 85

End of cycle, lights out.

​

 

[Bill.de.Cat]

They sell plastic welding kits at harbor freight….that way you have filler…probably more expensive than a new piece…

Although jb weld would work, I suppose…

JB has a plastic epoxy kit I used on a jeep steering pump res. Over 400 for the new pump, they don't just sell the res and for 7.99 I glooped it up and it was still holding 4 years later when I sold it.

 

[Bill.de.Cat]

I thought about that, melt a zip tie on it maybe. That is on the table, but kinda later option because I could end up melting the whole thing lol.

I'd just just the main valve off, pull the connector, blow it out dry, silicone it and reinstall tomorrow. your pots won't dry out that much over 24 hours.

 

[N/A-Greengo]

​