Indoor Duckster gives Wilma a go

:slap:
Any time you take personal injury for the greater good of the growing community you deserve a thanks. Just imagining the moment of impact and the WTF moment immediately after. New design strategy, weed splatter. Now that’s money
 
Another batch of BHO today.30g each of BBG, WC, & GSC. Chopped and air dried for a few extra days down to 50% rh, so it weighed about 85g going into the tube. I kept to the method I used last time with 2 exceptions. I went back to using a silicone mat to line my pyrex pan. This time I used a warm water double boiler during the butane boil off. The boil off was quicker and more uniform so the double boiler appears to have merit. After the butane had drained, I closed the valves. I noticed a bit of ice in the material. After the liquid butane was gone I was able to pour off the water droplets. I put the mat in the vacuum chamber and the material behaved like I saw in the videos this time.

It took a couple of hours before a got round to bringing to tube in to clean it. I did not open either of the valves before taking off the clamp - bigggggggggg mistake. As soon as the clamp released, a sound like a pistol shot, the endcap/valve, gasket, and a shotgun blast of weed hits me in the chest. From the next room I hear, "What was that?" A few seconds later, "Are you alright?" Then the misses peeks round the corner and stares at me till she realizes that I'm ok. Then she burst out laughing. The kitchen and everything in it are covered in weed. It was even inside some of the drawers and cabinets. We spent the next 2-1/2 hours cleaning up the mess.

Now I'm not sure if I relieved all the pressure the first time of if pressure built up during the 2 hours the tube was sitting outside with the valves closed. Either way - note to self - open the valve before removing the end clamp dumbass! Not sure how much pressure it was but I'm sure it was less than 5psi. Sure glad it wasn't more!
[emoji23][emoji23][emoji23][emoji23]Shouldn't laugh but we nearly had a flying duck [emoji44][emoji16]be careful you loon [emoji106]

Sent from my CLT-L09 using Tapatalk
 
Another batch of BHO today.30g each of BBG, WC, & GSC. Chopped and air dried for a few extra days down to 50% rh, so it weighed about 85g going into the tube. I kept to the method I used last time with 2 exceptions. I went back to using a silicone mat to line my pyrex pan. This time I used a warm water double boiler during the butane boil off. The boil off was quicker and more uniform so the double boiler appears to have merit. After the butane had drained, I closed the valves. I noticed a bit of ice in the material. After the liquid butane was gone I was able to pour off the water droplets. I put the mat in the vacuum chamber and the material behaved like I saw in the videos this time.

It took a couple of hours before a got round to bringing to tube in to clean it. I did not open either of the valves before taking off the clamp - bigggggggggg mistake. As soon as the clamp released, a sound like a pistol shot, the endcap/valve, gasket, and a shotgun blast of weed hits me in the chest. From the next room I hear, "What was that?" A few seconds later, "Are you alright?" Then the misses peeks round the corner and stares at me till she realizes that I'm ok. Then she burst out laughing. The kitchen and everything in it are covered in weed. It was even inside some of the drawers and cabinets. We spent the next 2-1/2 hours cleaning up the mess.

Now I'm not sure if I relieved all the pressure the first time of if pressure built up during the 2 hours the tube was sitting outside with the valves closed. Either way - note to self - open the valve before removing the end clamp dumbass! Not sure how much pressure it was but I'm sure it was less than 5psi. Sure glad it wasn't more!
[emoji23][emoji23][emoji23]

I reckon its where you left it outside. That's a fair old hike up in temp. The weed would of still been near freezing. [emoji3587][emoji3540][emoji91][emoji1658][emoji378][emoji95]

Sent from my LDN-L01 using Tapatalk
 
Thanks lads. I included the bit about my little mistake partially as a warning - don't follow my dumbass lead. But mostly because it was fookin hilarious. Pity [HASHTAG]#2[/HASHTAG] granddaughter wasn't home when it happened, she would have taken lots pictures. The wife is not a techy type - she still has a flip phone that she never uses. And I usually don't think of taking pictures during these memorable occasions. :face::rofl::rofl::crying::crying:

Time for wake n bake [HASHTAG]#2[/HASHTAG] with a little BHO:pass::baked:
 
Another batch of BHO today.30g each of BBG, WC, & GSC. Chopped and air dried for a few extra days down to 50% rh, so it weighed about 85g going into the tube. I kept to the method I used last time with 2 exceptions. I went back to using a silicone mat to line my pyrex pan. This time I used a warm water double boiler during the butane boil off. The boil off was quicker and more uniform so the double boiler appears to have merit. After the butane had drained, I closed the valves. I noticed a bit of ice in the material. After the liquid butane was gone I was able to pour off the water droplets. I put the mat in the vacuum chamber and the material behaved like I saw in the videos this time.

It took a couple of hours before a got round to bringing to tube in to clean it. I did not open either of the valves before taking off the clamp - bigggggggggg mistake. As soon as the clamp released, a sound like a pistol shot, the endcap/valve, gasket, and a shotgun blast of weed hits me in the chest. From the next room I hear, "What was that?" A few seconds later, "Are you alright?" Then the misses peeks round the corner and stares at me till she realizes that I'm ok. Then she burst out laughing. The kitchen and everything in it are covered in weed. It was even inside some of the drawers and cabinets. We spent the next 2-1/2 hours cleaning up the mess.

Now I'm not sure if I relieved all the pressure the first time or if pressure built up during the 2 hours the tube was sitting outside with the valves closed. Either way - note to self - open the valve before removing the end clamp dumbass! Not sure how much pressure it was but I'm sure it was less than 5psi. Sure glad it wasn't more!

[emoji23][emoji23][emoji23] Flashbacks from ‘Nam?
 
Getting the tent cleaned up and all of the gear ready for another go. Discovered one of the chillers had crapped out so had to replace it with the spare. Not sure what it's going to be this time. One with most likely be a fast buds gorilla glue, but sure on the other yet. Narrowed it down to one of several Mephisto pips - Livers n cheese, Bubbly Livers (where do they come up with these names), Gold Glue, or S.O.D.K.
 
Back
Top