Whiddow v2

[Noideakush]

So. This is my second whiddow and I've made some changes hoping for better results. So as I stated I was gonna upgrade my light from the little viparspectra 300w to something more substantial so within my budget I got a sf1000. And it's cool. I ran some go green by professors nutriants through my coco and a little ph down also. Put my sead in the cyco pearl coco and now the waitimg begins. Have had a bit of a dig and the seads cracked with a tail hanging out of it so hopefully it wont be long and will breach the surface and the fun will start. I now have my weather station so I can monitor humidu and temp. My dehumidifier. My intent heater aswell as my usual nutes and ppm metre. Wish me luck. Still very much a learner but each one I do I hope I get a little better

 

[Noideakush]

It's a girl. Well better be. So I've got my light up at 30 inches.. this thing so far is a sick light. Have a little spray in the tent. Lights on about 60% humidity is up but I don't mine being so young. I'll keep the spray going a while just until I get some good roots forming before its given a feed. Probably a week or so away though. Gotta make sure I dont over water like usual Haha.

 

[Noideakush]

Not alot of difference today. Set my light timer to 18/6 dropped my light to 24" havent watered yet. Humidity is at 60% and 20°c. Hopefully itll be full steam ahead soon.

 

[knoxie]

Quick question, why not dim the lights and just move them closer, thus lowering your electricity bill? Cuz i can only see one plant.

 

[Noideakush]

Quick question, why not dim the lights and just move them closer, thus lowering your electricity bill? Cuz i can only see one plant.

I just go off the recommended light hights. Led use very little power. Lights to high itll stretch. Lights too low will stunt. I'm still working on the dimmer side of things but my very limited experience light height is super important. Power isnt expensive enough to worry

 

[Noideakush]

Haha, thank you for explaining it for me, kinda stoned on some shit i grew!
P.S it was my first grow and it was beautiful, wish you the best of luck brudda! ✌

Thanks man. I'm not saying it's not possible but from what I've seen lights too close makes it all fluffy. Hopefully this one I'll get them even tighter

 

[Noideakush]

Now take off Haha. Each plant I learn a little more and i think it makes it better the next time. Even the simple things that i always forget. Dont over water is the one i really need to work on. Pre charging my coco with proffesors nutrients go green may have helped me as it's got calcium and magnesium in it. So keen to start feeding her but one day at a time. Keep it basic.
Correct light height
Correct temperature and humidity
And dont over water/feed

 

[Noideakush]

My plant is approximately 32mm across it's true leaves. I'm unsure weather to feed it or let the second set come out. Trying so hard to not over water. Temp is at 20°c and 50%rh. This is always the point my plants just stop dead in there tracks. Any ideas why. @Fitzy @Garage_Grower @oldfart

 

[Django_TO]

My plant is approximately 32mm across it's true leaves. I'm unsure weather to feed it or let the second set come out. Trying so hard to not over water. Temp is at 20°c and 50%rh. This is always the point my plants just stop dead in there tracks. Any ideas why. @Fitzy @Garage_Grower @oldfart

Are you able to raise RH? At that point i have like 80% RH. Even at 20°c you can raise RH to 70% with no problem. Get a vpd table. The easyest way to raise RH at that stage is to make small plastic domes (you can cut bottom of plastic jugs or bottles and make some small holes) and put it over the girl.

 

[Noideakush]

Are you able to raise RH? At that point i have like 80% RH. Even at 20°c you can raise RH to 70% with no problem. Get a vpd table. The easyest way to raise RH at that stage is to make small plastic domes (you can cut bottom of plastic jugs or bottles and make some small holes) and put it over the girl.

Any reason to raise it