Indoor Blueberry cookies

[Bob's Auto's]

Ladies look alright brother. Sometimes you'll see a certain pheno take multiple weeks longer.
I had the same with the Mephisto's Wedding. One was short and sticky and finished in 68 days or so, the other would have taken 100+days to finish and got chopped to make rosin out of.

 

[Noideakush]

they look fine to me, but the overcrowding and mass of large fans would drive me to distraction, get in there and defol like a man posessed, In my very humble opinion you really, really need to defol like your life and the lives of your plant depended on it....







the ones with smaller buds look like they have a lot more Sativa genes with those long thin leaves... so they are likely to slower and longer flowering.... but what do I know 





I struggle removing leaves cos I always feel like I'm taking the wrong ones. The fans are only 6 inch I think and have 2 up above and 1 below. That makes sense about the sativa genetic but then I thought they would be taller and more lanky. I'll do some more leaf stripping tomorrow. I've filled over a garbage bag already and can't even notice it

 

[Noideakush]

Ladies look alright brother. Sometimes you'll see a certain pheno take multiple weeks longer.

I had the same with the Mephisto's Wedding. One was short and sticky and finished in 68 days or so, the other would have taken 100+days to finish and got chopped to make rosin out of.

Yeah right. I've never had them this far apart before. Will have to be a split harvest. Whats your go to for making rosin. I've just done my first keif co2 run

 

[Bob's Auto's]

I've got a DIY rosin press. So that's what I use to press.

 

[Noideakush]

I've got a DIY rosin press. So that's what I use to press.

Any instructions on how to make one. Keen to have a crack at it

 

[Bob's Auto's]

Any instructions on how to make one. Keen to have a crack at it

Can you weld and do you have a knowledge of electricity? ie, connect a wire to a post? If so, very easy!!
Think I sourced the materials for under 200$
I'll have to look if I can find the Fusion files if you want them
Found them. These are a couple of screenshots. If you want the files I can WeTransfer you a link via PM

 

[Noideakush]

Can you weld and do you have a knowledge of electricity? ie, connect a wire to a post? If so, very easy!!



Think I sourced the materials for under 200$



I'll have to look if I can find the Fusion files if you want them



Found them. These are a couple of screenshots. If you want the files I can WeTransfer you a link via PM 







Yeah cool. Then just bought heat pads

 

[Bob's Auto's]

I even build the heatblocks themselves. ordered two pieces of aluminum stock, drilled the holes for the heating elements. Drilled some holes and tapped them with thread so they could be mounted on the plates.
In the drawing there's one thing missing and that's a jack. I welded a 6mm steal plate on top of the jack and mounted the bottom heatplate on it. The top one goes into the frame.

 

[Corum59]

I even build the heatblocks themselves. ordered two pieces of aluminum stock, drilled the holes for the heating elements. Drilled some holes and tapped them with thread so they could be mounted on the plates.
In the drawing there's one thing missing and that's a jack. I welded a 6mm steal plate on top of the jack and mounted the bottom heatplate on it. The top one goes into the frame.

Gotta love it when "handymen" get out their toys and create, just for the fun of it all.

 

[Noideakush]

I even build the heatblocks themselves. ordered two pieces of aluminum stock, drilled the holes for the heating elements. Drilled some holes and tapped them with thread so they could be mounted on the plates.

In the drawing there's one thing missing and that's a jack. I welded a 6mm steal plate on top of the jack and mounted the bottom heatplate on it. The top one goes into the frame.

Thats sick. I need to get onto this