Indoor Need Some Suggestions On This New Cab

[micro.grower]

I would def say only run a few plants for this grow. Of they stay small, u could always add a couple more. If four out grow your box, well, ur Sorta screwed. At least wait till you get some practice at Lst and other training methods. I promise u homie, my first two grows were single plant grows. I.m just now getting comfortable growing more than four in either of my cabs. This 8 cup auto grow j have going now is completely experimental. U can hope for the best but be prepared for the worst...

 

[p.l.u.r]

Lowryder#2, AKR's, Big Devils, AK47's all fem autoflowers, Im placing another bean order was thinking of trying some Mi5 and something else, havent decided, Im also ordering from AFN store, I sent the money out but I must have wrote something wrong because I got it back yesterday.

Given the right method, you could have some big plants, normally if I was growing 4 id germinate 7.. And select the plants with the best characteristics and female.. I still think youll struggle with 4! id go for 3. Its the magic number!!

Lookin forward to seeing this grow up and running bro..

Peace..

 

[jhnfrmrby420]

Ok, It looks like I'll do 3. What is LST, I know nothing about it

 

[p.l.u.r]

here is a guide mate..

https://www.autoflower.org/f7/lst-how-info-guide-5085.html

Basically its slowly tying your plant up through its growth so that the main cola stays level with the lower branches, through doing this the whole canopy of the plant receives an even distribution of light... I have slightly trained my current plant as it got too big lol.. Cant complain..

Peace..

 

[jhnfrmrby420]

OK, went over and put a few hrs into my new dresser cab, here's what I got so far. The top panel is where Im putting the fan and filter. Then in that back panel Im cutting in a vent that the filtered air will exit. I was going to put the exhaust in the middle of the ceiling, or is there a better place????????. Im putting 2 pvc elbow for light traps and intake air on each side, probably 2 or 3 inch, so there will be 4 total. Since there is space under the dresser I will put them up through the floor into the cab. Im also going to paint and caulk everything. Then Im gettin to work on a cfl DIY light fixture. I'll post progress pics as I go. I glued every joint with gorilla glue that stuff is amazing, but it swells, so thats the foam looking stuff all over the wood, I cleaned it up it the last 2 pics. Im also putting a felt seal around the door and behind that top plate where fan and filter will be, That panel unscrews to have access in there.

 

[Stunted]

Looking good so far

:smokebuds:

 

[realcarlos]

Very nice
High 5

 

[p.l.u.r]

Looks like you have been busy bro.
what do you mean by ceiling? Are you going to exhust heat/smell from room aswell as from cupboard?
Keep up the good work bro.. Ill be watching..
peace..

 

[jhnfrmrby420]

Thanks for the compliments, it means alot....P.L.U.R. Meaning the ceiling in the cab, which will go into that 8 inch space up top. Pic #5 shows the access door off that 8 inch area where the fan and filter will be, the vent to vent filtered air will be in that cover thats off. If you look at pic 1, you'll see the plywood, (the ceiling) of the grow area, above the plywood is the sealed off area where tha fan and stuff is going

 

[p.l.u.r]

I think for best air circulation you should put air output on side oppersite to air intake(but still in "ceiling") so all fresh air that comes in the bottom will travel across the plant.. But that said with good enough internal circulation anywhere on top would be fine..