Photoperiod White berry and Hindu kush closer grow

Update here at 6 weeks from sprout. These are both now at 11 days of 12/12. Hindu kush really showing the indica will definitely be a bush at 17 inches maybe hits 20..The white berry as really grown is at 20.5 inches now and thinking should have few more days of height growth so I'm guessing 2ft area.
First flowering booster water today.
 
White berry is on left. 42days since sprout.
Hindu kush on right at 40days since sprout.
20170915_132741.jpg
20170915_132752.jpg

Hindu kush
20170915_132905.jpg

White berry
20170915_132921.jpg
 
Hey man those plants look realllly healthy, very nice, you're doing a great job with the nutrition.

If you can get some poly film for the walls, that would be a great investment for your garden. I'm worried about moisture and mold trapped behind that paper you have put up everywhere. If black/white poly is out of your budget, you can usually get a good semi-gloss white bathroom paint on sale for less than $20 and a roller and tray is another $10. That would really improve your garden and prevent the humidity from causing you problems later on!

Keep up the great work man, and I think indoor is exactly where your thread belongs. This isn't a micro grow.

:greenthumb:
 
Thanks a lot for your input! I try to stay on top of nutrients and use the correct amount. Now I've been doing indoor for about a year and a half and started using nutrients a few grow a ago I think I got down a good cycle. They just really pushed out noticeable buds today at 14 days 12/12.
I am going to take your advice! The paper was a temp thing a few grows ago but then I never got poly..where can I find Poly? Price isn't a big deal to me. Can I get at a lowes or home depot? I actually notice the paper looks kind of damp in the pictures great call I'm going to remove it now.
 
Cool man! That should be a good temporary solution I hope? :)

Honestly, if I were you I'd get the low-odor zero VOC semi-gloss enamel paint. It will be cheaper than poly and easier to install!

The stuff you are looking for is called "Panda Film" its 4mm poly and it's black on one side and white on the other.

If budget isn't an issue, some of my friends swear by mylar coated styrofoam insulation panels. They're even easier to install than painting but might cost more. They're definitely available at lowes.

Personally, I'm using the paint.
 
Subbed, nice grow @imlovenuggets, I have to confess I following this guy above , he's full of little gems if information :thumbsup: so I hope you don't mind me sitting in and enjoying ya grow ,and that :pass:
 
Thanks @hairyman this should be where the grow gets fun to watch. I shall take the advice! I just going back to work tomorrow from shoulder surgery so money bit tight atm haha. I'll do one of the 2 suggested options.

Question, I notice on the kush plant not much secondary node development compared to the white berry...is that just a strain thing that can vary?
 
looking good,and in a nice lil spot to.
i thought that flat matt white paint was strangely more reflective that gloss.though it may seem more reflective tinfoil is worse than paint,tinfoil can also cause hot spots because of the way light bounces off it.and the dull side is better.i allways thought a growroom full of mirrors would be great,but mirrors absorb way more light than they reflect.weird science shit dosnt allways make sense.
diamond mylar,standard mylar,that black one side white the other,flat white paint.
im sure ive read them tidbits of info somewhere,i couldnt have dreamt it could i ?
keep er lit.
:pighug:
 
Thanks, yes the hot spots I thought there was something with foil like that. Well hopefully it will be ok for a week or two I'll just keep a eye out for any signs of hot spot areas until then. It's not terrible dimmer on sides but enough to be noticeable.
 
Back
Top