Grow Room 2.5 sf auto grow adventure

[Animatey]

New growth is looking good, color is lighter. So far so good dude!

Sent from my Moto G (5) Plus using Tapatalk

 

[Tejasdirt]

Day 21 from germ
Sorry for crappy pic it’s a cell phone thing.
Both have had light training.
Basically tied down the bottom 4 branches to
Let in more light.
These pic was taken dureing lites off so the leaves are relaxed.
The plant on the right the new growth ion top is a much lighter green almost pale.
Will get a better pic of it this evening.

 

[Tejasdirt]

Day 22 from germ
Here’s the mutation on the top of right plant.
Not all that concerned
Waiting to see new growth
Could be from before changes were made
Lowered MegaC to 450 ppm
Raised up fan speed due to summer heat
QB is ten inches above plant

 

[Bigg Al]

View attachment 1085489 Day 27 from germ
Here’s the mutation on the top of right plant.
Not all that concerned
Waiting to see new growth
Could be from before changes were made
Lowered MegaC to 450 ppm
Raised up fan speed due to summer heat
QB is ten inches above plant

That high ppm is burning the new growth, I'd give semi flush and lower ppm's.

 

[Tejasdirt]

The ppms were 550-600
Semi flush was done yesterday
The new base line gonna be shooting for is Around 450ppm.
450 ppm MC was watered in yesterday.
Now going to pay attention to color as ppms have been lowered
@Bigg Al
Think ppms should be lower than 450ppm??

 

[Bigg Al]

The ppms were 550-600
Semi flush was done yesterday
The new base line gonna be shooting for is Around 450ppm.
450 ppm MC was watered in yesterday.
Now going to pay attention to color as ppms have been lowered
@Bigg Al
Think ppms should be lower than 450ppm??

I'd back down to 300-350

 

[elcoloan]

yay! another hempy user! i'll be following this thread!
may i ask two things?
1. how do you start your seeds?
2. what temps do you have in that space?

 

[Tejasdirt]

@Bigg Al
Next watering in 2 days, the baseline will be lowered to 350ppm.
And the base will stay at 350 for the whole grow.

@elcoloan

I am growing in a cab that uses ambient air. The temps hover around 76-80 degrees depending on room temp.
As far as germ goes
I soak for 24 hours.
While soaking I take a rapist rooter plug and cut about 1/4 inch off the pointed end.
I then insert into the tray pictured above, cut end up.
After 24 hours I stick the seed about 1/8 inch into the cut end of the rapid rooter.
Place into above tray
Mist liberally
Close and place on my router for 1-3 days till seed pops out.
I then take the seed in the rapid rooter and put into the hempy bucket and start the hempy tech.
Im sure your wondering what the rapid rooter germ tray is.
It a “eggy” tray
( tapes covering vent holes)
You know
The best way to boil a egg as shown on tv.
The eggy sucked
But their packaging works like a charm!!!

 

[Tejasdirt]

day 23 from seed germination
Lights on
The tied down branches have already turned up!!!

I can’t believe I’m comteplateing sticking one more auto in there!!

 

[Tejasdirt]

Day 24 from seed germination

Just noticed just a minute smigen of tip burn on the right plant.
No worried as tomorrow is watering day and and as per @Bigg Al I’ll be bringing the megacrop down to 350ppm
Also got some serious leave bending I’ve been doing to combat that defoilazation itch