Hey Friends
Three days on and most of the seeds have germinated or at least have cracked. I started with a cleanup job which I should have done earlier, but then I'm lazy
For the third time I'm reusing this soil and I just dumped the old root stubs with the leftover soil from last time in the tub with the leftover soil. Gave it a couple of good punches and this is what I was left with. I don't know anymore who asked me a while ago, but the roots don't have issues going through those pouches...
View attachment 1549581
I mixed this old dry soil with the soil in the barrel...No need to add anymore amendments at this time as 50% of the soil is still unused and has been brewing for more then three months with the Startrex and Silicium Flash. When needed I can topdress the soil with the Silicium Flash as need be, but I don't think we'll need to be doing that
View attachment 1549580
I filled up the 3.5L / 0.92gal pots with about 1/2L or two Solocups full of soil.
View attachment 1549567
Then it was time to take out the big guns. For this round BioTabs provided me with two ten packs of them BioTabs.
View attachment 1549568
I dropped one whole BioTab in a corner on top of the soil...I had been contemplating if I should crack them, but I decided against it and just dropped one whole tab in each pot.
View attachment 1549569
Then topped of the pots until the brim. I didn't press the soil or anything. I try to keep it as fluffy as possible while the worms start to take hold in the soil.
View attachment 1549570
Next up the seeds.
As I said, most seeds did germinate. About four weren't cracked yet. I've set them aside until tomorrow to check if more seeds did germinate. Anyhow, I had enough sprouts to sow into the pots.
View attachment 1549572
Full house!!
I figured out it was easier to transfer the tray with the pots without first watering them, so there I went to the tent. Once there I had a bit of an issue getting the try into the tent as both are 60x60... An empty tray is easy, but filled with sixteen pots...Food for thought.
Some of you might have noticed, but I put some plastic tape around the pots to keep them together during transport. This has probably save my skin while squeezing the tray inside the tent...
View attachment 1549573
Installed my trusty NodeMCU with temperature, humidity, lux and CO2 sensor drop in the middle of the table and slided the whole unit as low as I could get it so the lux sensor give an approx. value of the light intensity.
View attachment 1549574
As usual just before watering I measured five teaspoons of Bactrex and dropped it into 5L of water.
View attachment 1549575
Before watering the pots I dispenced one teaspoon of Mycotrex on top of the soil and worked that in with my fingers.
View attachment 1549576
I'm trying to be very careful with the amount of water I'm giving these pots. First of the soil was already 'moist', not wet...though. I'll try to photograph how I water one of the next times...
View attachment 1549577
Set the extraction fan to the below setting. I didn't have time to hack it yet, so this grow will probably be adjusted via this knob.
View attachment 1549578
The TS-1000 on the other hand is completely controlled by my Blynk app. The blue light is the NodeMCU inside the plastic box.
View attachment 1549579
And these are the values inside the tent after a couple of hours running before I placed the pots inside the tent and now an hour after placing the pots inside.
The temperature is a bit on the low side, so I'm going to adjust the light a bit from 66 to 75%, this will probably raise the temperature enough for the seedlings to enjoy it's heat and grow, grow, grow!!!
I've also ordered a 55x55cm 48Watt heating mat to put underneath the tray. This will aid me in the winter to keep the tent up to temperature without light poisoning my ladies. And since the values which my CO2 meter gives are a bit to high to be correct I've ordered a newer, bit more expensive (like 4 times more expensive) sensor.
View attachment 1549588
Regards,
Bob