Mañ'O'Green and GreenLeaf 2 part for Autos

[durbanpoisoner]

Great spreadsheet, thanks! Would you perhaps add a section for sweet candy in addition to bud explosion?

On a different note. Just switched to MC2 from canna a+b. I was expecting the nutes to mix up cloudy and dark but surprisingly it mixed up clear Curious to see the PH stability with the silica and whether I’ll actually need to add calmag with MC2 in coco. The first 5gal mixture I didn’t include any additional calmag.

 

[CannabisMingus]

eed to add calmag with MC2 in coco.

I would be surprised if you don't. Let us know man!

 

[durbanpoisoner]

It would surprise me too but greenleaf says that they include enough calcium and magnesium to not require it. Im at the end of my run and only have a few weeks left. I’ll keep an eye on it

Gauging whether something is a deficiency or a lockout is not always easy. What I’ve learned this time is less is more with nutes. Feed a mild EC and increase fertigation if needed. Up EC only if really necessary.

 

[InkAddict$]

Yes that is exactly what I do. I make 1 gallon of Part A at the strength for 10 gallons, I make 1 gallon of Part B at the strength for 10 gallons. After 1 day of fertigating my six plants drain to waste, The reservoir has dropped from 600PPM to 450 ish. By adding 1/3 of the gallon of part a and 1/3 of a gallon of part b the reservoir is returned to the balanced 600 PPM start. I also manually add .66g Epsom Salt. I just eyball the 1/3 gallon lines but it is close enough. I mix the gallons twice a week for 6 days total then I drain and clean the res and start fresh with the next weeks formula.

I don't have a res? I got a 5 gal bucket I can mix in? I'm confused!!! On should I just cut what you mix in half? Then fill my res of sip buckets with it?

 

[InkAddict$]

Transplant Day 420

View attachment 1309558

The Hugo grow blocks are soaked for 30 minutes in 5.5 PH nutrient solution. I put a generous teaspoon of Mykos in the holes, moisten it with run-off from the block and with gentle pressure push the seedling plug into the block. Put the block in the support system, apply the FloraFlex Cap and the algae shade. The blocks will now provide the water and nutrients for the plant for the next nine days. 18/6 light schedule starts now.

View attachment 1309557

One of the babies was not tall enough to fit the algae shade. I will apply it when possible.

View attachment 1309559

View attachment 1309560

Ok so this feeding schedule for 10 gal... What if I cut all your measurements in half for a 5gal bucket and mix? Then feed into each res of my sips? Now I do have bud explosion and sweet candy too! I'll add them but got half there recommended dose per gal? Or should I use what they recommend? I have everything but the bud candy and my humic acid is npk..... I'll try this and see how it works.... I'll use 50/50 ro/tap that should bring me to about 600ppm and pH around 6.... I also do earth juice microblast foliar spray once a week..... I just did it today... I mixed up everything yesterday and it came out to 600ppm and I didn't use but maybe half the recommendation...... I'll mix mc A/B in separate gallons then mix everything else in 3 gal in a 5 gallon bucket... Then add the mc.... I also use kelp4less cal-mag..... I'll add what it recommends..... Maybe less just to be safe.... What do you think?

 

[CannabisMingus]

Careful adding CalMag unless you are deficient. What's in your tap?

 

[InkAddict$]

Careful adding CalMag unless you are deficient. What's in your tap?

I keep getting deficiency's brown spots... I use 50/50 ro/tap.... My tap ppm is 150 pH of 10

 

[InkAddict$]

Careful adding CalMag unless you are deficient. What's in your tap?

When I mix ro it comes out 50 ppm...

 

[Mañ'O'Green]

I keep getting deficiency's brown spots... I use 50/50 ro/tap.... My tap ppm is 150 pH of 10

Probably not a deficiency - after all you keep putting it in.

It is getting locked up. Too much or out of balance nutrients.

When I mix ro it comes out 50 ppm...

Your meter defaults to the lowest number it can read. Most TDS meters do not work below 50 PPM or your meter is out of specification. They do wear out.

 

[InkAddict$]

I would be surprised if you don't. Let us know man!