Hi, so this is my first forum post as-well as my first grow with auto flowers, so excuse me if it sounds a little dumb or like Idk how to ask the question. So I guess what I’m having trouble with is recently I noticed my plants started going into flowering which is bad ass considering how healthy I’ve raised these bad boys (or should I say girls?) anyways I’m using 2 1500W KingLED lights, fox farm ocean followed with voodoo juice and big buds advanced nutrients. And Ph my water at 6.0-6.5. And use 10 gal grow bags. I had them on veg mode and changed them to bloom when I noticed that the pistels started coming out heavy. I use a 18/6 light cycle. I read that it’s more better if I use both veg and bloom mode to give it the full spectrum but my plants did not like it at all. I grow in a closet and keep the door open with the ceiling fan on so I’m not sure if it’s because of the heat that caused them to droop or not so I switched to just leaving the bloom on but I noticed recently that one of the 2 started drooping and canoeing a little, I’m not sure if it’s because of the big buds or because of the bloom lighting I keep the lights 2ft away from the plants and did the hand test but that shouldn’t be a reason could it be the big buds nutrients?
Auto flower slight canoeing along with slight wilt
- Thread starter Mcnasty713
- Start date
- Joined
- May 12, 2020
- Messages
- 2,743
- Reputation
- 3,040
- Reaction score
- 10,233
- Points
- 0
- Currently Smoking
- slaughtered Lamb BY SAWNEY BEAN
Hello what is your RH as if its to low the leaves start to tacco or canoeing to conserve moisture
Hello what is your RH as if its to low the leaves start to tacco or canoeing to conserve moisture
TBH I don’t even know I didn’t even know cannabis plants had RH levels lol, how would I go about increasing these RH levels if it is to low?
- Joined
- May 12, 2020
- Messages
- 2,743
- Reputation
- 3,040
- Reaction score
- 10,233
- Points
- 0
- Currently Smoking
- slaughtered Lamb BY SAWNEY BEAN
Hello RH is the water moisture in the air not the plant you want to have a RH of 50% roughly
| Life stage | Air temperature | Humidity |
|---|---|---|
| Vegetation | 24 – 27°C | 40 – 70% |
| Flowering | 24 – 27°C | 40 – 50% |
| Late flowering | 21 – 27°C | 30 – 50% |
| Drying | 21°C | 50% |
Hello RH is the water moisture in the air not the plant you want to have a RH of 50% roughly
Life stage Air temperature Humidity Vegetation 24 – 27°C 40 – 70% Flowering 24 – 27°C 40 – 50% Late flowering 21 – 27°C 30 – 50% Drying 21°C 50%
Ooooh ok I see now, so would lowering the fan speed be beneficial to raising RH levels? Rn it’s on full speed 24/7 and I think that’s probably what’s drying the air out then.
- Joined
- Feb 14, 2018
- Messages
- 3,110
- Reputation
- 431
- Reaction score
- 10,018
- Points
- 0
- Currently Smoking
- La Buena Hierba Panama Haze
You need to measure your temperature and humidity levels then input them on this VPD calculator
The hand test has never been accurate because you have to account for light levels as well. I'd set the lights at the manufacturers suggested height for bloom. I can't say if there's an issue with your nutrients or soil pH but if there is an issue a good place to start is your environment.
They don't look bad though but I'm not going to guess at what is wrong without more info
The hand test has never been accurate because you have to account for light levels as well. I'd set the lights at the manufacturers suggested height for bloom. I can't say if there's an issue with your nutrients or soil pH but if there is an issue a good place to start is your environment.
They don't look bad though but I'm not going to guess at what is wrong without more info
- Joined
- May 12, 2020
- Messages
- 2,743
- Reputation
- 3,040
- Reaction score
- 10,233
- Points
- 0
- Currently Smoking
- slaughtered Lamb BY SAWNEY BEAN
Hello you need to get temperature and humidity reader to start with slowing the fan wont add RH to the air you need a humidefier for that but first you need to know what your RH is first and temps before you can do anything
Hello you need to get temperature and humidity reader to start with slowing the fan wont add RH to the air you need a humidefier for that but first you need to know what your RH is first and temps before you can do anything
ok cool I’ll get right on that then, thanks for the tips man you guys have been a great help. I’ll be back to give you guys an update once I get those 2 things under control
So upon ordering the thermostat for the temp and humidity I went to water them and noticed these little brown twisted tips on the leaves as-well as these weird outlines on the leaf vein. Could this be Nute burn? or heat stress? I’m having a hard time differentiating
Attachments
Similar threads
