Extraction How I do it

[Ripper]

after tons of research I order CCell cartridges in .5 ML these are supposed to be the best cartridges.

The mathe that I have found that works well o 1/2 gram of rosin and 12 drops of liquid terpenes. I have now made 20 cartridges and they work very very well here. Is a photo of one

This was an older style ccell cartridge. I have the newer ones now

So I use a shot glass and a hot plate. I use my hot plate on the low setting (150 degrees) and I can lace my rosin (1/12 gram) in a shot glass and let it melt. I then add 12 drops of terpenes and mix it thoroughly (about 10 minutes. After it looks clear I set the shot glass on the table and let it cool down. After it cools I make sure it has the same consistency as honey. After I like the consistency I take a syringe with a blunt tip needle and I load it into the cartridge. Let it sit for 30 min and smoke away. The flavor is amazing.

 

[Recycled]

Here. I’ll be following along...


Sent from my iPhone using Tapatalk

 

[Ripper]

Here. I’ll be following along...


Sent from my iPhone using Tapatalk

I will put up a picture tutorial tomorrow and a few videos of others I have found on YouTube

 

[Recycled]

I will put up a picture tutorial tomorrow and a few videos of others I have found on YouTube

Excellent man. I’m still saving for my press but trying to get more edumucated on vape.


Sent from my iPhone using Tapatalk

 

[Ripper]

Excellent man. I’m still saving for my press but trying to get more edumucated on vape.


Sent from my iPhone using Tapatalk

I am learning new stuff as well. The goal is to put together a kick ass forum to help others.

 

[Autotron]

@Ripper Where do you get your terpenes from? Any general guidelines about things to consider when picking them and things to look for? As for the rosin, is this just straight up rosin pressed with heat and pressure in a press? Or do you do anything to it before you do the steps you outlined above? This seems great, because I was always under the impression that you needed to thin it out a lot with VG and PG to get it to the right consistency to be used in a cartridge.

Looking forward to following along!

 

[Ripper]

@Ripper Where do you get your terpenes from? Any general guidelines about things to consider when picking them and things to look for? As for the rosin, is this just straight up rosin pressed with heat and pressure in a press? Or do you do anything to it before you do the steps you outlined above? This seems great, because I was always under the impression that you needed to thin it out a lot with VG and PG to get it to the right consistency to be used in a cartridge.

Looking forward to following along!

I get my terpenes from one of two websites.

Massterpenes.com and I get terp liquify from 760glass.com neither product has VG or PG in it.

I press .5 grams of rosin and add 12 to 14 drops of terpenes on a hot plate set at 150 degrees and stir it till it is clear as in make sure there are no un melted parts or particles in it. I then let it cool to room temperature to check the consistency which should be the same as honey. Once I am satisfied I load it in a syringe and put it in a cartridge. Pretty simple process.

 

[oldcoot]

Hey ripper, if i buy licks, can that be used to thin all types of concentrates.
I have everclear wax, co2 and distalite.
Will this work on all.
Also does the original have no flavor.

 

[Ripper]

Hey ripper, if i buy licks, can that be used to thin all types of concentrates.
I have everclear wax, co2 and distalite.
Will this work on all.
Also does the original have no flavor.

What are licks? What original? Sorry bud I am confused.

 

[McDee]

What are licks? What original? Sorry bud I am confused.

Licks is an emulsifier you mix equal parts with rosin. Put it on a little heat and they mix together to make ejuice. Works but I stopped using it, makes me cough to much. I believe you can use as tincture as well. Also you can mix with flower but have not tried.